FC 10

Multi purpose fast setting and hardening hydraulic mortar

Fast setting cement based compound which sets within 10 min. It is recommended for various fast applications such as fixing heating panels, door frames. It can be used for fast cement screed repairs, bonding tiles in repair jobs or for drain formation prior to the application of waterproofing mortars such as SC 200 PENETRATE or SC ELASTIC.

Consumption: 1,5 kg/m²/mm of thickness
Color: Grey
Package: Plastic bags 5 kg
Pallet: 720 kg


  • FC 10 quick-setting hydraulic cement mortar is suitable for:
    • quick concrete repairs indoors and outdoors
    • leaks on cementitious surfaces
    • construction of wells where they will receive liquids in a short time
    • installation of electrical panels
    • ppot restorations up to 50 mm filling gaps and minor defects
    • tiling in repairs
  • Form: powder
  • Application thickness: 1 - 50 mm
  • Workability: approx. 10 minutes / 20°C
  • Application temperature: from +5°C up to +35°C

Substrate preparation:

The application substrate must be structurally stable, completely clean without grease, oil, loose elements, and anything else that may affect the flow and reduce the adhesion of FC 10 to it. The minimum tensile strength of the substrate must be at least 1,5 N/mm². Existing cracks on the substrate should be bonded with the fluid epoxy resin EPO FLUID. On the still fresh EPO FLUID surface, scatter S 500 silica sand or similar to create a mineral surface.

Preparation of the mix:

Mix the content of the 5kg paper bag containing FC 10 with 1,2 1,3 liters of clean and fresh water by means of appropriate electrical stirrer at low speed (500 rpm) until a viscous uniform mortar free of lumps is obtained. The mortar must be used within the next 10 minutes (in a temperature of +20°C). Higher temperatures reduce and lower temperatures increase the working time of the


FC 10 is applied, immediately after stirring, to a well-soaked surface, without stagnant water, using a trowel or spatula. Concentrate the material with the help of a spatula, to ensure full contact of the mortar with the substrate. In the case of a local leak repair, press firmly on the application point for a few minutes until it hardens. The material will be heated gradually until the hydration reaction is complete.


FC 10 shouldn’t be applied:

  • In cases where the substrate and environment temperature is less than +5°C or higher than +35°C
  • On substrates with tensile strength less than 1,5N/mm²
  • Directly on anhydrite, metal or flexible substrates or substrates subjected to rising humidity
  • On substrates not properly prepared or primed
  • On friable or non-properly cured substrates
  • Over existing expansion joints
  • Under direct sunlight and/or strong drying wind

Also note the following:

  • Do not add cement, gypsum, lime or other binders or substances which may affect the mortar characteristics
  • Application should be performed by professional skilled workers


Tools, buckets, tiles, etc. can be cleaned with fresh and clean water as long as FC 10 mix is still fresh. After hardening occurs, cleaning can take place by mechanical means.

Legal Notice:

The technical data and recommendations included or listed are the outcome of laboratory measurements combined with our current knowledge and expertise. All information and specifications should in any case be considered as indicative. The Company makes every effort to ensure the accuracy of the information provided herein. Product specifications are subject to change without notice and may differ from product images. Due to printing and application procedures, the colors displayed here should be considered as indicative. In particular, variations in materials, substrates and on-site application conditions are such that no warranty can be given or implied reference to the suitability of the materials for trading or use for a particular purpose and conditions of any given project. Anyone interested in using the product must ensure beforehand that the product is suitable for the intended use and in any case, the user is solely responsible for any outcomes associated with the use of product. Among other things, the Company is not responsible for any normal wear or tear from environmental or any other unsuitable conditions. We reserve the right to revise or change the data herein without prior notice. Restrictions and disclaimers apply to the extent permitted by applicable law. The Company has a Technical Support Department, which has exclusive responsibility for providing technical advice and solutions, addressing relevant issues. Requests to the Technical Support Department are addressed and answered, only in writing. For the latest and valid version of the Technical Data Sheet, the user of the material must refer to our website www.novamix.gr.