WATER PRIMER EPX

Two component water based epoxy primer free of solvents for absorbent substrates that require consolidation

Two-component, water-based epoxy primer for in depth consolidation of absorbent substrates. It has a great penetrating ability and forms barrier to rising moisture of up to 4%. When applied prior to the use of cement-based coatings such as self-levelling compounds like PLANO 120 S/F or microcement coatings PLANOCOLOR MICROCEMENT, PLANOCOLOR GRANULATES S 500 silica sand must be scattered on the final coat, while it is still fresh.

Consumption: 100-150 ml/m²
Package: Containers (2+1) L

Description

WATER PRIMER EPX can be used:

    • as primer for reinforcing concrete substrates and screeds
    • for normal to high absorbent substrates
    • as adhesive primer for smoothing and laying mortars
    • as primer for NOVAMIX decorative coatings

 

  • Form: liquid
  • Working time:
    • 1 hour ≈ 30°C
    • 2 hours ≈ 23°C
    • 2,5 hours ≈ 10°C
  • Walkability:
    • 4 hours > 25°C
    • ≈ 8 hours > 12°C
  • Application temperature: from +10°C up to +30°C

Substrate preparation:

The surface to which WATER PRIMER EPX is to be applied, should be clean, dry and free from dust. The substrate must be insulated and not subject to rising moisture. The maximum permissible moisture content of the surface must not exceed 4%. The application surface temperature (caution not ambient temperature) should be between + 10°C and + 30°C.

Preparation of the mix:

Before mixing, stir component A separately with a low speed electric mixer. Then add component B completely to component A. Mixing of the two components is done for about 2-3 minutes with an electric mixer at low speed. It is important to stir both the walls and the bottom of the container so that the catalyst goes everywhere evenly. Allow the mix to rest for a few minutes. The end of the workability is not recognized by the increase in viscosity, so it is necessary to apply the material within the specified time.

Application of the mix:

Apply the mix in a continuous (non-interruptive) layer using a suitable varnish roller or brush. In any case, ensure that the material penetrates well in the treated surface. If necessary, apply a second coat. If it is to follow the application of cementitious products after the adhesive coating has dried, it is considered necessary to spray on the still wet surface quartz sand such as S 500.

Recommendations:

  • Do not apply when the temperature is lower than +10°C and the relative humidity of the atmosphere exceeds 80%, or when there is a possibility of rain and wet weather
  • Do not apply on substrates with rising moisture
  • Apply an additional coat if more than 24 hours pass before coating
  • The two components of WATER PRIMER EPX are in a premeasured proportion so never mix partially the two components
  • The end of the workability is not recognized by the increase in viscosity, so it is necessary to apply the material within the specified time
  • Do not apply WATER PRIMNER EPX upon old varnishes and dusty or dirty surfaces
  • Always use appropriate and clean tools
  • The application has to be performed by a professional user

Cleaning:

Buckets, tools, coatings etc. can be cleaned with water as long as the mix is still fresh. Once dried cleaning can be done only by mechanical means.

Legal Notice:

The technical data and recommendations included or listed are the outcome of laboratory measurements combined with our current knowledge and expertise. All information and specifications should in any case be considered as indicative. The Company makes every effort to ensure the accuracy of the information provided herein. Product specifications are subject to change without notice and may differ from product images. Due to printing and application procedures, the colors displayed here should be considered as indicative. In particular, variations in materials, substrates and on-site application conditions are such that no warranty can be given or implied reference to the suitability of the materials for trading or use for a particular purpose and conditions of any given project. Anyone interested in using the product must ensure beforehand that the product is suitable for the intended use and in any case, the user is solely responsible for any outcomes associated with the use of product. Among other things, the Company is not responsible for any normal wear or tear from environmental or any other unsuitable conditions. We reserve the right to revise or change the data herein without prior notice. Restrictions and disclaimers apply to the extent permitted by applicable law. The Company has a Technical Support Department, which has exclusive responsibility for providing technical advice and solutions, addressing relevant issues. Requests to the Technical Support Department are addressed and answered, only in writing. For the latest and valid version of the Technical Data Sheet, the user of the material must refer to our website www.novamix.gr.